Although wireless is more convenient for many individuals, owing to multimedia sharing, bandwidth on a home network, and wireless security concerns, you may prefer to employ a hard wired option for home networking. A wired cat6 Ethernet network at home provides you with a private, high-speed network for internet access, file sharing, media streaming, online gaming, IP security cameras, and other purposes.
How to Connect Cat6 Cable
Wiring a cat6 Ethernet connection isn’t as complicated as you would think, and it allows you a multitude of possibilities for customizing your home network. Connecting a cat6 plenum Ethernet cable is a simple solution to improve network administration. This is a straightforward and easy procedure of how to connect cat6 cable, and we’ve included everything you need to get started in this handy post. So, how do you go about wiring your own Cat6 cables?
What Exactly Is a Cat6 Ethernet Cable?
Ethernet cables, often known as network cables, are used to link two network nodes. In most households, this sort of cable will connect your router/switch to your computer, allowing them to communicate at fast rates. An Ethernet cable is made up of two major components: a UTP cable and an RJ45 header connection. UTP (unshielded twisted pair) cables are available in a variety of configurations, including Cat6, Cat5e, and Cat5.
Cat6 cables have a bandwidth of 10 Gbps at 250 MHz, but Cat5e can only achieve one gigabit per second, allowing Cat6 cables to transport more data. No matter what sort of cable you choose, the RJ45 connection on the end of an Ethernet cable will always be the same. It is worth mentioning that shielded RJ45 connectors and Cat6 cables can be utilized in crosstalk-prone situations.
Cat6 Ethernet Cable Wiring (With an RJ45 Connector)
So, when it comes to how To connect cat6 cable, wiring your own cat6 Ethernet wire is simpler than you would think, at least if you have got the necessary knowledge. The instructions below will assist you in completing the tricky elements of the procedure. This includes both T-568A and T-568B configurations since they both meet ANSI/TIA-568-C wiring standards.
You may use any configuration for your network cables as long as they are the same on both ends of the Cat6 wire. This procedure will necessitate the use of a number of instruments and components.
- Wire stripper/side cutters
- An RJ45 crimping tool
- 1 x Cat6 cable length
- RJ45 connectors (two)
1. Cut the Cable to the Desired Length.
The first stage in this procedure is the most straightforward. All you have to do is cut the cable to the proper length. We are going to use side cutters for this. However, you may use any type of wire cutter as long as it is powerful enough to cut the cat6 cable.
When doing this, a piece of string may be used as a measuring instrument, making it easier to measure around corners and tight locations. Place the cable between the jaws of your cutting tool and apply pressure to achieve a level cut.
2. Copper Cable Stripping
Then, remove your copper wiring to liberate the inner twisted pairs. When you do this, you just need to remove approximately an inch from either end of the wire, leaving enough room for the RJ45 connector to easily fit on the end.
3. Twisted Pairs Preparation
You will need to perform a bit more stripping now, as well as arrange the twisted pairs in the correct locations. Inside the cat6 1000ft cable, you are working with are four sets of twisted pairs and a little plastic X-shaped separator. You may just snip the partition away. Untwist the little cables so that they can be moved separately.
Then gently take about 1/4 inch of insulation from each of the small wires. The cores of the wires are solid, making it simple to prevent a large mess. Now you may arrange your wires to fit the figure, taking care to ensure proper orientation.
4. Connecting the Wires to the RJ45 Plug
After you have sorted your wires, it’s time to plug them into the RJ45 socket. This might be a difficult task, so attempt to insert all of the cables at the same time. Before you crimp the wires, they must go as deep into the jack as they can go.
5. Crimping Cat6
RJ45 jacks are intended to operate with universal crimping equipment, making this part of the procedure quick and uncomplicated. Simply place your RJ45 connection correctly in the teeth of the crimping tool before pushing down firmly. When you look through the clear plastic shell of the connection, you will be able to check if all of the wires are properly placed.
6. Put Your Cat6 Patch Cable to the Test
You will be able to test your cat6 Ethernet cable once you have properly wired both ends. You may purchase network cable testers to ensure that you have completed the operation correctly, but you can also connect your cable to your computer and a router/switch to ensure that the connection is strong and reliable.
It’s doubtful that you will get it just correctly the first time. This is a tricky project that will take some time to master, but a little patience will go a long way.
What Are the Advantages of Installing Your Own Cat6 Cables?
Wiring your own cat6 cabling is a fantastic method to save money and space while also creating a clean network that is simple to live with. Large rolls of cat6 cabling and bags of RJ45 connectors may be purchased online, making this option far more convenient than locating a bulk Ethernet cable source.
Cat6 Wiring Made Easy
As previously said, wiring your own cat6 plenum Ethernet cable is simple, and you now have all the information you need to get started. The most essential thing to keep in mind is to cut as neatly and accurately as possible. Accurately cutting your Cat6 wire makes crimping and connecting the connector a pleasure. You’ll wonder why you didn’t connect your own Cat6 Ethernet wires previously!
